A satellite dish is the first step in any home satellite TV installation.
But in some parts of the world, the price is astronomical.
In places like China, it’s hard to even find a decent dish.
A few of us have tried to build our own, but it’s a lot of work.
So, what are you going to do?
And how do you make your own dish?
Here are the steps.
Step 1: Get the right parts You need to have a good quality antenna.
If you have a crappy antenna, you’re just going to end up with a bunch of crap hanging out of the back of your home.
This will ruin your home TV setup.
So get a good antenna that has a good diameter.
And if you want to build a dish, you need a good dish mount.
A dish mount will have a metal plate and a plastic or fiberglass core.
It has to be strong enough to hold the satellite dish.
Step 2: Build the dish There are several different types of dish mounts, but they all have a common goal.
They want to hold an antenna that is a certain diameter and is strong enough for the dish.
And they will all work together.
This means that a dish that has an extra diameter will work just fine with a larger dish.
Here’s what you should do: Cut out the aluminum sheet.
The thickness of the aluminum is important because you want it to hold up in the dish without bending or breaking.
If it’s too thin, the dish will be easily bent.
Make a template out of a sheet of cardboard.
The template is important.
It will help you shape the shape of the dish so it doesn’t bend when the dish is placed.
Measure the diameter of your dish and add some more.
If the diameter is less than a few millimeters, cut out the sheet of paper.
This is to make sure that you’re not cutting into the thickness of your antenna.
For example, if your dish is 5 centimeters, it should be about 8 millimeters.
If your dish has a diameter of 10 centimeters, cut it out again to make a template.
Make sure you don’t cut too far into the metal sheet.
Make the template and cut the template out.
Make some marks on the template.
These will help with the bending.
This next step is where it gets tricky.
You want to make the dish out of aluminum foil.
You don’t want it too thin.
The thicker the aluminum foil, the more weight the dish can carry.
Make this mark by placing a little bit of aluminum onto a piece of paper and tracing a line along the edge.
You can make this mark in any direction.
You may have to make it bigger or smaller.
The easiest way to make this marks is to hold a pencil in the middle of the line.
Then just make a mark with your pencil and draw a line that runs from the edge of the paper to the center of the mark.
Now mark where the line starts and ends.
You should make the marks about 3 centimeters apart.
Make another mark about 2 centimeters away from where the first one ends.
This line should be perpendicular to the previous one.
Now trace the line you made with the pencil.
This time you will make a slight diagonal slash.
Trace the slash along the metal foil, then make another diagonal slash about 2 millimeters away from the first slash.
Make these marks about 4 centimeters apart from the previous marks.
The next step on the paper is to cut out your foil template.
This part is tricky.
It depends on the diameter you’re looking for.
For my 6.5 centimeters dish, the first mark is about 1.5 millimeters across and the next mark is 3 millimeters to the right.
This gives a diameter that’s about 1 inch across.
You’ll also want to mark the line where you made the diagonal slash with your other hand.
If a thinner foil has a smaller diameter, you may want to cut it more thin, to make more marks.
So this next part is a bit tricky.
The first mark on the foil template will be about 1 millimeter long.
The second mark is only about 1 meter long.
So the next step will be to cut the second mark out with a sharp knife and mark it with a marker.
You’re not going to need this marker on your next cut, because you’ll make the mark at the end of the template instead.
This step is important, because it will make sure you cut out all the lines you made in the template when you’re done.
You need the template to make your marks so you don to make mistakes when cutting the aluminum.
If one of the marks is too short, you’ll have to cut off a bit of the top of the plate so you have enough space to make another mark on your new plate.
This last step is the hardest.
The aluminum foil is really thin. You won’t